vcc_gnd
/
esp-who
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
esp-who/components/bus/i2c_bus.c

489 lines
20 KiB
C
Raw Blame History

// Copyright 2020-2021 Espressif Systems (Shanghai) PTE LTD
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
// http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
#include <stdio.h>
#include <inttypes.h>
#include <string.h>
#include "freertos/FreeRTOS.h"
#include "freertos/semphr.h"
#include "esp_log.h"
#include "i2c_bus.h"
#define I2C_ACK_CHECK_EN 0x1 /*!< I2C master will check ack from slave*/
#define I2C_ACK_CHECK_DIS 0x0 /*!< I2C master will not check ack from slave */
#define I2C_BUS_FLG_DEFAULT (0)
#define I2C_BUS_MASTER_BUF_LEN (0)
#define I2C_BUS_MS_TO_WAIT CONFIG_I2C_MS_TO_WAIT
#define I2C_BUS_TICKS_TO_WAIT (I2C_BUS_MS_TO_WAIT/portTICK_RATE_MS)
#define I2C_BUS_MUTEX_TICKS_TO_WAIT (I2C_BUS_MS_TO_WAIT/portTICK_RATE_MS)
typedef struct {
i2c_port_t i2c_port; /*!<I2C port number */
bool is_init; /*if bus is initialized*/
i2c_config_t conf_active; /*!<I2C active configuration */
SemaphoreHandle_t mutex; /* mutex to achive thread-safe*/
int32_t ref_counter; /*reference count*/
} i2c_bus_t;
typedef struct {
uint8_t dev_addr; /*device address*/
i2c_config_t conf; /*!<I2C active configuration */
i2c_bus_t *i2c_bus; /*!<I2C bus*/
} i2c_bus_device_t;
static const char *TAG = "i2c_bus";
static i2c_bus_t s_i2c_bus[I2C_NUM_MAX];
#define I2C_BUS_CHECK(a, str, ret) if(!(a)) { \
ESP_LOGE(TAG,"%s:%d (%s):%s", __FILE__, __LINE__, __FUNCTION__, str); \
return (ret); \
}
#define I2C_BUS_CHECK_GOTO(a, str, lable) if(!(a)) { \
ESP_LOGE(TAG,"%s:%d (%s):%s", __FILE__, __LINE__, __FUNCTION__, str); \
goto lable; \
}
#define I2C_BUS_INIT_CHECK(is_init, ret) if(!is_init) { \
ESP_LOGE(TAG,"%s:%d (%s):i2c_bus has not inited", __FILE__, __LINE__, __FUNCTION__); \
return (ret); \
}
#define I2C_BUS_MUTEX_TAKE(mutex, ret) if (!xSemaphoreTake(mutex, I2C_BUS_MUTEX_TICKS_TO_WAIT)) { \
ESP_LOGE(TAG, "i2c_bus take mutex timeout, max wait = %"PRIu32"ms", I2C_BUS_MUTEX_TICKS_TO_WAIT); \
return (ret); \
}
#define I2C_BUS_MUTEX_TAKE_MAX_DELAY(mutex, ret) if (!xSemaphoreTake(mutex, portMAX_DELAY)) { \
ESP_LOGE(TAG, "i2c_bus take mutex timeout, max wait = %"PRIu32"ms", portMAX_DELAY); \
return (ret); \
}
#define I2C_BUS_MUTEX_GIVE(mutex, ret) if (!xSemaphoreGive(mutex)) { \
ESP_LOGE(TAG, "i2c_bus give mutex failed"); \
return (ret); \
}
static esp_err_t i2c_driver_reinit(i2c_port_t port, const i2c_config_t *conf);
static esp_err_t i2c_driver_deinit(i2c_port_t port);
static esp_err_t i2c_bus_write_reg8(i2c_bus_device_handle_t dev_handle, uint8_t mem_address, size_t data_len, const uint8_t *data);
static esp_err_t i2c_bus_read_reg8(i2c_bus_device_handle_t dev_handle, uint8_t mem_address, size_t data_len, uint8_t *data);
inline static bool i2c_config_compare(i2c_port_t port, const i2c_config_t *conf);
/**************************************** Public Functions (Application level)*********************************************/
i2c_bus_handle_t i2c_bus_create(i2c_port_t port, const i2c_config_t *conf)
{
I2C_BUS_CHECK(port < I2C_NUM_MAX, "I2C port error", NULL);
I2C_BUS_CHECK(conf != NULL, "pointer = NULL error", NULL);
I2C_BUS_CHECK(conf->mode == I2C_MODE_MASTER, "i2c_bus only supports master mode", NULL);
if (s_i2c_bus[port].is_init) {
/**if i2c_bus has been inited and configs not changed, return the handle directly**/
if (i2c_config_compare(port, conf)) {
ESP_LOGW(TAG, "i2c%d has been inited, return handle directly, ref_counter=%"PRIu32"", port, s_i2c_bus[port].ref_counter);
return (i2c_bus_handle_t)&s_i2c_bus[port];
}
} else {
s_i2c_bus[port].mutex = xSemaphoreCreateMutex();
I2C_BUS_CHECK(s_i2c_bus[port].mutex != NULL, "i2c_bus xSemaphoreCreateMutex failed", NULL);
s_i2c_bus[port].ref_counter = 0;
}
esp_err_t ret = i2c_driver_reinit(port, conf);
I2C_BUS_CHECK(ret == ESP_OK, "init error", NULL);
s_i2c_bus[port].conf_active = *conf;
s_i2c_bus[port].i2c_port = port;
return (i2c_bus_handle_t)&s_i2c_bus[port];
}
esp_err_t i2c_bus_delete(i2c_bus_handle_t *p_bus)
{
I2C_BUS_CHECK(p_bus != NULL && *p_bus != NULL, "pointer = NULL error", ESP_ERR_INVALID_ARG);
i2c_bus_t *i2c_bus = (i2c_bus_t *)(*p_bus);
I2C_BUS_INIT_CHECK(i2c_bus->is_init, ESP_FAIL);
I2C_BUS_MUTEX_TAKE_MAX_DELAY(i2c_bus->mutex, ESP_ERR_TIMEOUT);
/** if ref_counter == 0, de-init the bus**/
if ((i2c_bus->ref_counter) > 0) {
ESP_LOGW(TAG, "i2c%d is also handled by others ref_counter=%"PRIu32", won't be de-inited", i2c_bus->i2c_port, i2c_bus->ref_counter);
return ESP_OK;
}
esp_err_t ret = i2c_driver_deinit(i2c_bus->i2c_port);
I2C_BUS_CHECK(ret == ESP_OK, "deinit error", ret);
vSemaphoreDelete(i2c_bus->mutex);
*p_bus = NULL;
return ESP_OK;
}
uint8_t i2c_bus_scan(i2c_bus_handle_t bus_handle, uint8_t *buf, uint8_t num)
{
I2C_BUS_CHECK(bus_handle != NULL, "Handle error", 0);
i2c_bus_t *i2c_bus = (i2c_bus_t *)bus_handle;
I2C_BUS_INIT_CHECK(i2c_bus->is_init, 0);
uint8_t device_count = 0;
I2C_BUS_MUTEX_TAKE_MAX_DELAY(i2c_bus->mutex, 0);
for (uint8_t dev_address = 1; dev_address < 127; dev_address++) {
i2c_cmd_handle_t cmd = i2c_cmd_link_create();
i2c_master_start(cmd);
i2c_master_write_byte(cmd, (dev_address << 1) | I2C_MASTER_WRITE, I2C_ACK_CHECK_EN);
i2c_master_stop(cmd);
esp_err_t ret = i2c_master_cmd_begin(i2c_bus->i2c_port, cmd, I2C_BUS_TICKS_TO_WAIT);
if (ret == ESP_OK) {
ESP_LOGI(TAG, "found i2c device address = 0x%02x", dev_address);
if (buf != NULL && device_count < num) {
*(buf + device_count) = dev_address;
}
device_count++;
}
i2c_cmd_link_delete(cmd);
}
I2C_BUS_MUTEX_GIVE(i2c_bus->mutex, 0);
return device_count;
}
uint32_t i2c_bus_get_current_clk_speed(i2c_bus_handle_t bus_handle)
{
I2C_BUS_CHECK(bus_handle != NULL, "Null Bus Handle", 0);
i2c_bus_t *i2c_bus = (i2c_bus_t *)bus_handle;
I2C_BUS_INIT_CHECK(i2c_bus->is_init, 0);
return i2c_bus->conf_active.master.clk_speed;
}
uint8_t i2c_bus_get_created_device_num(i2c_bus_handle_t bus_handle)
{
I2C_BUS_CHECK(bus_handle != NULL, "Null Bus Handle", 0);
i2c_bus_t *i2c_bus = (i2c_bus_t *)bus_handle;
I2C_BUS_INIT_CHECK(i2c_bus->is_init, 0);
return i2c_bus->ref_counter;
}
i2c_bus_device_handle_t i2c_bus_device_create(i2c_bus_handle_t bus_handle, uint8_t dev_addr, uint32_t clk_speed)
{
I2C_BUS_CHECK(bus_handle != NULL, "Null Bus Handle", NULL);
I2C_BUS_CHECK(clk_speed <= 400000, "clk_speed must <= 400000", NULL);
i2c_bus_t *i2c_bus = (i2c_bus_t *)bus_handle;
I2C_BUS_INIT_CHECK(i2c_bus->is_init, NULL);
i2c_bus_device_t *i2c_device = calloc(1, sizeof(i2c_bus_device_t));
I2C_BUS_CHECK(i2c_device != NULL, "calloc memory failed", NULL);
I2C_BUS_MUTEX_TAKE_MAX_DELAY(i2c_bus->mutex, NULL);
i2c_device->dev_addr = dev_addr;
i2c_device->conf = i2c_bus->conf_active;
/*if clk_speed == 0, current active clock speed will be used, else set a specified value*/
if (clk_speed != 0) {
i2c_device->conf.master.clk_speed = clk_speed;
}
i2c_device->i2c_bus = i2c_bus;
i2c_bus->ref_counter++;
I2C_BUS_MUTEX_GIVE(i2c_bus->mutex, NULL);
return (i2c_bus_device_handle_t)i2c_device;
}
esp_err_t i2c_bus_device_delete(i2c_bus_device_handle_t *p_dev_handle)
{
I2C_BUS_CHECK(p_dev_handle != NULL && *p_dev_handle != NULL, "Null Device Handle", ESP_ERR_INVALID_ARG);
i2c_bus_device_t *i2c_device = (i2c_bus_device_t *)(*p_dev_handle);
I2C_BUS_MUTEX_TAKE_MAX_DELAY(i2c_device->i2c_bus->mutex, ESP_ERR_TIMEOUT);
i2c_device->i2c_bus->ref_counter--;
I2C_BUS_MUTEX_GIVE(i2c_device->i2c_bus->mutex, ESP_FAIL);
free(i2c_device);
*p_dev_handle = NULL;
return ESP_OK;
}
uint8_t i2c_bus_device_get_address(i2c_bus_device_handle_t dev_handle)
{
I2C_BUS_CHECK(dev_handle != NULL, "device handle error", NULL_I2C_DEV_ADDR);
i2c_bus_device_t *i2c_device = (i2c_bus_device_t *)dev_handle;
return i2c_device->dev_addr;
}
esp_err_t i2c_bus_read_bytes(i2c_bus_device_handle_t dev_handle, uint8_t mem_address, size_t data_len, uint8_t *data)
{
return i2c_bus_read_reg8(dev_handle, mem_address, data_len, data);
}
esp_err_t i2c_bus_read_byte(i2c_bus_device_handle_t dev_handle, uint8_t mem_address, uint8_t *data)
{
return i2c_bus_read_reg8(dev_handle, mem_address, 1, data);
}
esp_err_t i2c_bus_read_bit(i2c_bus_device_handle_t dev_handle, uint8_t mem_address, uint8_t bit_num, uint8_t *data)
{
uint8_t byte = 0;
esp_err_t ret = i2c_bus_read_reg8(dev_handle, mem_address, 1, &byte);
*data = byte & (1 << bit_num);
*data = (*data != 0) ? 1 : 0;
return ret;
}
esp_err_t i2c_bus_read_bits(i2c_bus_device_handle_t dev_handle, uint8_t mem_address, uint8_t bit_start, uint8_t length, uint8_t *data)
{
uint8_t byte = 0;
esp_err_t ret = i2c_bus_read_byte(dev_handle, mem_address, &byte);
if (ret != ESP_OK) {
return ret;
}
uint8_t mask = ((1 << length) - 1) << (bit_start - length + 1);
byte &= mask;
byte >>= (bit_start - length + 1);
*data = byte;
return ret;
}
esp_err_t i2c_bus_write_byte(i2c_bus_device_handle_t dev_handle, uint8_t mem_address, uint8_t data)
{
return i2c_bus_write_reg8(dev_handle, mem_address, 1, &data);
}
esp_err_t i2c_bus_write_bytes(i2c_bus_device_handle_t dev_handle, uint8_t mem_address, size_t data_len, const uint8_t *data)
{
return i2c_bus_write_reg8(dev_handle, mem_address, data_len, data);
}
esp_err_t i2c_bus_write_bit(i2c_bus_device_handle_t dev_handle, uint8_t mem_address, uint8_t bit_num, uint8_t data)
{
uint8_t byte = 0;
esp_err_t ret = i2c_bus_read_byte(dev_handle, mem_address, &byte);
if (ret != ESP_OK) {
return ret;
}
byte = (data != 0) ? (byte | (1 << bit_num)) : (byte & ~(1 << bit_num));
return i2c_bus_write_byte(dev_handle, mem_address, byte);
}
esp_err_t i2c_bus_write_bits(i2c_bus_device_handle_t dev_handle, uint8_t mem_address, uint8_t bit_start, uint8_t length, uint8_t data)
{
uint8_t byte = 0;
esp_err_t ret = i2c_bus_read_byte(dev_handle, mem_address, &byte);
if (ret != ESP_OK) {
return ret;
}
uint8_t mask = ((1 << length) - 1) << (bit_start - length + 1);
data <<= (bit_start - length + 1); // shift data into correct position
data &= mask; // zero all non-important bits in data
byte &= ~(mask); // zero all important bits in existing byte
byte |= data; // combine data with existing byte
return i2c_bus_write_byte(dev_handle, mem_address, byte);
}
/**
* @brief I2C master send queued commands.
* This function will trigger sending all queued commands.
* The task will be blocked until all the commands have been sent out.
* If I2C_BUS_DYNAMIC_CONFIG enable, i2c_bus will dynamically check configs and re-install i2c driver before each transfer,
* hence multiple devices with different configs on a single bus can be supported.
* @note
* Only call this function in I2C master mode
*
* @param i2c_num I2C port number
* @param cmd_handle I2C command handler
* @param ticks_to_wait maximum wait ticks.
* @param conf pointer to I2C parameter settings
* @return esp_err_t
*/
inline static esp_err_t i2c_master_cmd_begin_with_conf(i2c_port_t i2c_num, i2c_cmd_handle_t cmd_handle, TickType_t ticks_to_wait, const i2c_config_t *conf)
{
esp_err_t ret;
#ifdef CONFIG_I2C_BUS_DYNAMIC_CONFIG
/*if configs changed, i2c driver will reinit with new configuration*/
if (conf != NULL && false == i2c_config_compare(i2c_num, conf)) {
ret = i2c_driver_reinit(i2c_num, conf);
I2C_BUS_CHECK(ret == ESP_OK, "reinit error", ret);
s_i2c_bus[i2c_num].conf_active = *conf;
}
#endif
ret = i2c_master_cmd_begin(i2c_num, cmd_handle, ticks_to_wait);
return ret;
}
/**************************************** Public Functions (Low level)*********************************************/
esp_err_t i2c_bus_cmd_begin(i2c_bus_device_handle_t dev_handle, i2c_cmd_handle_t cmd)
{
I2C_BUS_CHECK(dev_handle != NULL, "device handle error", ESP_ERR_INVALID_ARG);
I2C_BUS_CHECK(cmd != NULL, "I2C command error", ESP_ERR_INVALID_ARG);
i2c_bus_device_t *i2c_device = (i2c_bus_device_t *)dev_handle;
I2C_BUS_INIT_CHECK(i2c_device->i2c_bus->is_init, ESP_ERR_INVALID_STATE);
I2C_BUS_MUTEX_TAKE(i2c_device->i2c_bus->mutex, ESP_ERR_TIMEOUT);
esp_err_t ret = i2c_master_cmd_begin_with_conf(i2c_device->i2c_bus->i2c_port, cmd, I2C_BUS_TICKS_TO_WAIT, &i2c_device->conf);
I2C_BUS_MUTEX_GIVE(i2c_device->i2c_bus->mutex, ESP_FAIL);
return ret;
}
static esp_err_t i2c_bus_read_reg8(i2c_bus_device_handle_t dev_handle, uint8_t mem_address, size_t data_len, uint8_t *data)
{
I2C_BUS_CHECK(dev_handle != NULL, "device handle error", ESP_ERR_INVALID_ARG);
I2C_BUS_CHECK(data != NULL, "data pointer error", ESP_ERR_INVALID_ARG);
i2c_bus_device_t *i2c_device = (i2c_bus_device_t *)dev_handle;
I2C_BUS_INIT_CHECK(i2c_device->i2c_bus->is_init, ESP_ERR_INVALID_STATE);
I2C_BUS_MUTEX_TAKE(i2c_device->i2c_bus->mutex, ESP_ERR_TIMEOUT);
i2c_cmd_handle_t cmd = i2c_cmd_link_create();
if (mem_address != NULL_I2C_MEM_ADDR) {
i2c_master_start(cmd);
i2c_master_write_byte(cmd, (i2c_device->dev_addr << 1) | I2C_MASTER_WRITE, I2C_ACK_CHECK_EN);
i2c_master_write_byte(cmd, mem_address, I2C_ACK_CHECK_EN);
}
i2c_master_start(cmd);
i2c_master_write_byte(cmd, (i2c_device->dev_addr << 1) | I2C_MASTER_READ, I2C_ACK_CHECK_EN);
i2c_master_read(cmd, data, data_len, I2C_MASTER_LAST_NACK);
i2c_master_stop(cmd);
esp_err_t ret = i2c_master_cmd_begin_with_conf(i2c_device->i2c_bus->i2c_port, cmd, I2C_BUS_TICKS_TO_WAIT, &i2c_device->conf);
i2c_cmd_link_delete(cmd);
I2C_BUS_MUTEX_GIVE(i2c_device->i2c_bus->mutex, ESP_FAIL);
return ret;
}
esp_err_t i2c_bus_read_reg16(i2c_bus_device_handle_t dev_handle, uint16_t mem_address, size_t data_len, uint8_t *data)
{
I2C_BUS_CHECK(dev_handle != NULL, "device handle error", ESP_ERR_INVALID_ARG);
I2C_BUS_CHECK(data != NULL, "data pointer error", ESP_ERR_INVALID_ARG);
i2c_bus_device_t *i2c_device = (i2c_bus_device_t *)dev_handle;
I2C_BUS_INIT_CHECK(i2c_device->i2c_bus->is_init, ESP_ERR_INVALID_STATE);
uint8_t memAddress8[2];
memAddress8[0] = (uint8_t)((mem_address >> 8) & 0x00FF);
memAddress8[1] = (uint8_t)(mem_address & 0x00FF);
I2C_BUS_MUTEX_TAKE(i2c_device->i2c_bus->mutex, ESP_ERR_TIMEOUT);
i2c_cmd_handle_t cmd = i2c_cmd_link_create();
if (mem_address != NULL_I2C_MEM_ADDR) {
i2c_master_start(cmd);
i2c_master_write_byte(cmd, (i2c_device->dev_addr << 1) | I2C_MASTER_WRITE, I2C_ACK_CHECK_EN);
i2c_master_write(cmd, memAddress8, 2, I2C_ACK_CHECK_EN);
}
i2c_master_start(cmd);
i2c_master_write_byte(cmd, (i2c_device->dev_addr << 1) | I2C_MASTER_READ, I2C_ACK_CHECK_EN);
i2c_master_read(cmd, data, data_len, I2C_MASTER_LAST_NACK);
i2c_master_stop(cmd);
esp_err_t ret = i2c_master_cmd_begin_with_conf(i2c_device->i2c_bus->i2c_port, cmd, I2C_BUS_TICKS_TO_WAIT, &i2c_device->conf);
i2c_cmd_link_delete(cmd);
I2C_BUS_MUTEX_GIVE(i2c_device->i2c_bus->mutex, ESP_FAIL);
return ret;
}
static esp_err_t i2c_bus_write_reg8(i2c_bus_device_handle_t dev_handle, uint8_t mem_address, size_t data_len, const uint8_t *data)
{
I2C_BUS_CHECK(dev_handle != NULL, "device handle error", ESP_ERR_INVALID_ARG);
I2C_BUS_CHECK(data != NULL, "data pointer error", ESP_ERR_INVALID_ARG);
i2c_bus_device_t *i2c_device = (i2c_bus_device_t *)dev_handle;
I2C_BUS_INIT_CHECK(i2c_device->i2c_bus->is_init, ESP_ERR_INVALID_STATE);
I2C_BUS_MUTEX_TAKE(i2c_device->i2c_bus->mutex, ESP_ERR_TIMEOUT);
i2c_cmd_handle_t cmd = i2c_cmd_link_create();
i2c_master_start(cmd);
i2c_master_write_byte(cmd, (i2c_device->dev_addr << 1) | I2C_MASTER_WRITE, I2C_ACK_CHECK_EN);
if (mem_address != NULL_I2C_MEM_ADDR) {
i2c_master_write_byte(cmd, mem_address, I2C_ACK_CHECK_EN);
}
i2c_master_write(cmd, (uint8_t *)data, data_len, I2C_ACK_CHECK_EN);
i2c_master_stop(cmd);
esp_err_t ret = i2c_master_cmd_begin_with_conf(i2c_device->i2c_bus->i2c_port, cmd, I2C_BUS_TICKS_TO_WAIT, &i2c_device->conf);
i2c_cmd_link_delete(cmd);
I2C_BUS_MUTEX_GIVE(i2c_device->i2c_bus->mutex, ESP_FAIL);
return ret;
}
esp_err_t i2c_bus_write_reg16(i2c_bus_device_handle_t dev_handle, uint16_t mem_address, size_t data_len, const uint8_t *data)
{
I2C_BUS_CHECK(dev_handle != NULL, "device handle error", ESP_ERR_INVALID_ARG);
I2C_BUS_CHECK(data != NULL, "data pointer error", ESP_ERR_INVALID_ARG);
i2c_bus_device_t *i2c_device = (i2c_bus_device_t *)dev_handle;
I2C_BUS_INIT_CHECK(i2c_device->i2c_bus->is_init, ESP_ERR_INVALID_STATE);
uint8_t memAddress8[2];
memAddress8[0] = (uint8_t)((mem_address >> 8) & 0x00FF);
memAddress8[1] = (uint8_t)(mem_address & 0x00FF);
I2C_BUS_MUTEX_TAKE(i2c_device->i2c_bus->mutex, ESP_ERR_TIMEOUT);
i2c_cmd_handle_t cmd = i2c_cmd_link_create();
i2c_master_start(cmd);
i2c_master_write_byte(cmd, (i2c_device->dev_addr << 1) | I2C_MASTER_WRITE, I2C_ACK_CHECK_EN);
if (mem_address != NULL_I2C_MEM_ADDR) {
i2c_master_write(cmd, memAddress8, 2, I2C_ACK_CHECK_EN);
}
i2c_master_write(cmd, (uint8_t *)data, data_len, I2C_ACK_CHECK_EN);
i2c_master_stop(cmd);
esp_err_t ret = i2c_master_cmd_begin_with_conf(i2c_device->i2c_bus->i2c_port, cmd, I2C_BUS_TICKS_TO_WAIT, &i2c_device->conf);
i2c_cmd_link_delete(cmd);
I2C_BUS_MUTEX_GIVE(i2c_device->i2c_bus->mutex, ESP_FAIL);
return ret;
}
/**************************************** Private Functions*********************************************/
static esp_err_t i2c_driver_reinit(i2c_port_t port, const i2c_config_t *conf)
{
I2C_BUS_CHECK(port < I2C_NUM_MAX, "i2c port error", ESP_ERR_INVALID_ARG);
I2C_BUS_CHECK(conf != NULL, "pointer = NULL error", ESP_ERR_INVALID_ARG);
if (s_i2c_bus[port].is_init) {
i2c_driver_delete(port);
s_i2c_bus[port].is_init = false;
ESP_LOGI(TAG, "i2c%d bus deinited", port);
}
esp_err_t ret = i2c_param_config(port, conf);
I2C_BUS_CHECK(ret == ESP_OK, "i2c param config failed", ret);
ret = i2c_driver_install(port, conf->mode, I2C_BUS_MASTER_BUF_LEN, I2C_BUS_MASTER_BUF_LEN, I2C_BUS_FLG_DEFAULT);
I2C_BUS_CHECK(ret == ESP_OK, "i2c driver install failed", ret);
s_i2c_bus[port].is_init = true;
ESP_LOGI(TAG, "i2c%d bus inited", port);
return ESP_OK;
}
static esp_err_t i2c_driver_deinit(i2c_port_t port)
{
I2C_BUS_CHECK(port < I2C_NUM_MAX, "i2c port error", ESP_ERR_INVALID_ARG);
I2C_BUS_CHECK(s_i2c_bus[port].is_init == true, "i2c not inited", ESP_ERR_INVALID_STATE);
i2c_driver_delete(port); //always return ESP_OK
s_i2c_bus[port].is_init = false;
ESP_LOGI(TAG,"i2c%d bus deinited",port);
return ESP_OK;
}
/**
* @brief compare with active i2c_bus configuration
*
* @param port choose which i2c_port's configuration will be compared
* @param conf new configuration
* @return true new configuration is equal to active configuration
* @return false new configuration is not equal to active configuration
*/
inline static bool i2c_config_compare(i2c_port_t port, const i2c_config_t *conf)
{
if (s_i2c_bus[port].conf_active.master.clk_speed == conf->master.clk_speed
&& s_i2c_bus[port].conf_active.sda_io_num == conf->sda_io_num
&& s_i2c_bus[port].conf_active.scl_io_num == conf->scl_io_num
&& s_i2c_bus[port].conf_active.scl_pullup_en == conf->scl_pullup_en
&& s_i2c_bus[port].conf_active.sda_pullup_en == conf->sda_pullup_en) {
return true;
}
return false;
}
Reference in New Issue View Git Blame Copy Permalink